To use a jointer planer, first make sure the machine is properly set up and adjusted. Then, run the stock along the jointer blades to create a flat surface. Finally, feed the stock into the planer to create a smooth finish.
- Set the jointer planer on a firm, level surface
- Adjust the cutting depth to your desired amount
- Turn on the jointer planer and feed your workpiece into the machine at a moderate speed
- Let the jointer planer do its work and remove your workpiece when it has been cut to your desired thickness/width
94 – Jointer & Planer, Exactly How to Use Them, What They Are, What They Do, Why You Might Need Both
Table of Contents
What is a Jointer Planer And What Does It Do
A jointer planer is a tool that is used to join two pieces of wood together. It consists of a base, a blade, and a handle. The blade is inserted into the base and then the handle is used to push the blade through the wood.
The blade cuts the wood as it goes, creating a smooth, even surface.
How Do I Use a Jointer Planer to Get the Best Results
Assuming you would like tips on how to use a jointer plane:
A jointer plane is one of the most essential hand planes for working with wood. Its long sole and bevel-up blade configuration make it ideal for truing wide boards and getting rid of twist.
Here are some tips to get the best results when using a jointer plane:
1. First, adjust the blade so that it protrudes about 1/8” from the body of the plane. You can do this by loosening the knob at the back of the plane and moving the blade forwards or backwards.
2. Next, set your fence so that it is perpendicular to the sole of the plane. To do this, loosen the thumbscrew on the side of the fence and rotate it until it is at a 90 degree angle to the sole. Then, tighten up the thumbscrew again to lock it in place.
3. Now you’re ready to start planing! Place your workpiece againstthe fence, making sure that it is flush with one side ofthe fence (this will ensure that you get an even cut). Apply light pressure as you pushthe plane forwards – you should only needto apply moderate pressure if yourblade is sharpened properly.
Asyou push forward, keep an eye outfor any tearout or chipping – ifyou see either of these happenings,simply adjust your technique untilyou achieve a clean cut.
What are Some Common Mistakes People Make When Using a Jointer Planer
There are several common mistakes people make when using a jointer plane. The most frequent mistake is not jointing the workpiece square to the blade. This can be easily corrected by setting the fence at 90 degrees to the table.
Another common mistake is not feeding the workpiece evenly into the blade. This can cause tear out or burning of the wood. It is important to keep an even pressure on both hands when feeding the workpiece into the blade.
The last common mistake is not keeping the blades sharp. Jointer planes need to be sharpened frequently to avoid damage to the wood and poor results.
Credit: www.wwgoa.com
How to Use a Jointer for Edge
Assuming you already have a jointer and know the basics of how to use it, here are some tips on how to get the best results when edge jointing.
1. Use a sharp cutterhead – This seems like a no-brainer, but making sure your cutterhead is sharp will make a big difference in the quality of your edge jointing. A dull cutterhead will tear out the wood instead of cutting it cleanly, resulting in an uneven surface.
2. Set up your boards properly – Before you start edge jointing, make sure your boards are flush with each other and that their edges are perfectly straight. If they’re not, your joints will be uneven.
3. Use a push block – A push block helps keep your fingers safe while you’re feeding the board through the jointer.
It also helps keep the board from slipping, which can cause problems with your joints.
4. Take light cuts – When you’re first starting out, take very light cuts (no more than 1/16″ per pass) until you get a feel for how much pressure to apply to the board and how fast to feed it through the machine. Taking too deep of a cut can result in damage to your jointer or an uneven surface on your boards.
Conclusion
A jointer planer is a great tool for any woodworker, especially those who are just starting out. Here are some tips on how to use a jointer planer:
1. Before using the jointer planer, make sure that the blades are sharp and in good condition.
If they are not, they can damage the wood.
2. When setting up the machine, make sure that the fence is square to the table. This will ensure that your cuts are straight.
3. To avoid tear-out, always feed the wood into the machine with the grain running parallel to the blades.
4. Take small cuts when you first start using the machine. As you become more comfortable with it, you can take larger cuts.
