How to Rig a Planer for Trolling

There are a few things you need to do in order to rig a planer for trolling. First, you need to tie the planer to the back of the boat. Second, you need to put some weight on the other end of the line so that it sinks down into the water.

Third, you need to attach your lures or bait to the line. Fourth, you need to let out enough line so that the planer can sink down deep enough into the water. Fifth, once everything is all set up, you can start trolling!

  • Choose the right planer for the job
  • A heavier planer is better for trolling in deeper water, while a lighter planer is better for shallower water
  • Attach the planer to your fishing line
  • Use a swivel to attach theplaner to your line, so it can rotate freely and won’t get tangled
  • Add weight to the planer if needed
  • This will help it sink more slowly and stay down in the water column where the fish are swimming
  • Set the depth of the planer using the adjustment knob on top of the device
  • You’ll want to experiment with different depths until you find where the fish are biting
  • Finally, cast out your line and let the planer do its work! The goal is to have your bait swim just above

How to Rig Planers for Trolling

How Do You Troll Planer Boards?

There are a few different ways that you can troll with planer boards, and the method that you use will largely depend on the type of fish that you’re targeting. In general, though, the process involves attaching your lure or bait to the planer board and then trolling it behind your boat at a slow speed. This will cause the planer board to zigzag back and forth across the water, which can be effective in attracting fish.

One of the most popular ways to troll with planer boards is to target walleye. When doing this, it’s often best to use live bait such as minnows or leeches. Attach your bait to the planer board using a snap swivel, and then troll at a speed of 1-2 mph.

The key is to keep your line relatively tight, as this will help ensure that the bait stays close to the bottom where walleye are often found feeding. Another common way to troll with planer boards is for salmon and trout. For these fish, lures such as spinners or spoons can be very effective.

Again, attach your lure to the snap swivel on the planer board and then troll at a slow speed behind the boat. Varying your speed and depth can also be helpful in attracting fish when trolling with planer boards.

How Do You Rig Up Planer Boards?

Planer boards are an essential tool for any serious angler, allowing you to fish multiple lines at once while still maintaining control over each individual line. While there are many different ways to rig up planer boards, the following instructions will show you one of the most commonly used methods. 1) First, you’ll need to determine where on your boat you’ll be mounting the planer boards.

Most people like to mount them on the gunwales or transom, but anywhere that provides easy access and doesn’t interfere with other gear or lines is fine. Once you’ve chosen a spot, use a drill to make pilot holes for the bolts or screws you’ll be using to attach the planer board brackets. 2) Next, it’s time to assemble the planer boards themselves.

If you’re using store-bought boards, this simply involves attaching the release clip (or clips) to one side of the board. If you’re making your own boards, you’ll need to do a bit more work, but thankfully there are plenty of plans and diagrams available online if you need help. 3) Now it’s time to attach the planer boards to your boat.

Start by threading a length of strong cord or rope through the hole in each bracket, then tie it off securely so that the board is held firmly in place. You may need someone else to help hold the board in place while you do this. 4) Finally, rig your lines as usual and clip them onto the release clips on your planer boards.

When everything is ready, cast out and let your lines play out behind the boat as usual -the planer boards will keep them from getting tangled up together!

How Do You Attach a Trolling Planer Bridle?

A trolling planer bridle is a device that is used to slow down a lure or bait when it is being pulled through the water. It is attached to the line above the lure or bait and has two arms that extend out to the sides. The arms are adjustable so that they can be moved closer together or further apart.

When the arms are close together, it creates more drag on the lure or bait and causes it to slow down. The farther apart the arms are, the less drag there is and the faster the lure or bait will move through the water. There are many different ways to attach a trolling planer bridle, but one of the most popular methods is using a snap swivel.

First, you will need to tie one end of the bridle line to the eyelet at the front of the snap swivel. Next, thread the other end of the bridle line through both arms of the planer bridle and then back through only one arm.

How Fast Can You Troll With Planer Boards?

There’s no definitive answer to this question as it largely depends on the size and weight of your planer boards, as well as the speed and power of your trolling motor. However, as a general rule of thumb, you can expect to troll with planer boards at speeds between 1-2 mph.

How to Rig a Planer for Trolling


How to Use a Trolling Planer

If you’re an avid fisherman, then you know how important it is to have the right gear. One essential piece of equipment is a trolling planer. Trolling planers are devices that help you control your boat’s speed and depth while fishing.

In this article, we’ll show you how to use a trolling planer so that you can get the most out of your fishing trips! First, let’s talk about how a trolling planer works. Basically, it’s a device that attaches to your boat and has a line running through it.

The line is connected to a release mechanism, which allows you to adjust the amount of line that’s released. This in turn controls the depth and speed of your boat. Now that we know how it works, let’s talk about how to use it.

First, attach the trolling planer to your boat according to the manufacturer’s instructions. Next, determine the depth at which you want to fish and set the release mechanism accordingly. Finally, cast your line into the water and start trolling!

As you can see, using a trolling planer is relatively simple once you know what you’re doing. By following these steps, you’ll be able to control your boat’s speed and depth with ease – giving you more time to focus on reeling in those big catches!


Are you an avid fisherman looking to step up your trolling game? If so, rigging a planer is a great way to add some excitement (and success) to your fishing trips. But how do you rig a planer?

Here are the basics: You’ll need a few supplies before you get started, including a planer, line, leader, sinker, and bait. Once you have everything, attach the planer to the line using a swivel.

Then tie the leader to the other end of the swivel and add your sinker about 18 inches above the planer. Finally, bait your hook and you’re ready to go! Planers are great for trolling because they help keep your line in the water at different depths.

This increases your chances of attracting fish and can lead to more successful fishing trips overall. So if you’re looking to take your trolling game to the next level, give rigging a planer a try!


Leave a Comment